Page 1 of 1

DIY NVIDIA 3D Vision emitter

Posted: Sun Feb 25, 2018 12:06 pm
by lukis101
Anybody seen this topic?
After 2 years, I finally made myself to properly cleanup the code and build a more stable setup. (Software-only sync was good enough for while)...

Thanks to previous hackers from this forum, I was able to hack/make myself an emitter without even having seen one irl! :geek:
After a few code and platform iterations, here's what I can offer:

Code:
Source available on GitHub
Built using a makefile and avr-gcc. I've used Atmel Studio, but should be possible to use toolchain included with Arduino IDE.
(I can upload a binary, but a lot of stuff is hard-coded...)

Hardware:
(Arduino) Pro Micro. ~5$ for a clone from China
And an IR LED(s) + transistor + resistors combo for actual signal transmission.

In the current state, software sync is not enough and can jitter a lot, SO:
A) Use external hardware sync signal. Currently accepts VESA sync, but with a few changes it can accept raw VSync.
B) Try to tweak backlight strobe and shutter frame timings + duty cycles to minimize jitter for your own setup.
C) Contribute to the project - a timer needs to be setup and kept in sync via the extra USB packet data.

Multiple protocols are already added. G05-A universal glasses that I have seem to support a lot of protocols, including 3D-vision one!
Stay way from Sony glasses, they appear to alternate polarity instead of full-blanking! (Anybody wanna buy a set? :D)

Attached a picture of my "setup":
2 status leds + 1w IR led for wide range, switched via mosfet. (added the 100ohm resistor only for the sake of a safer example)
Sync signal going to pin 2 from monitor (From DVI2LVDS to be exact :twisted:)

Re: DIY NVIDIA 3D Vision emitter

Posted: Thu Mar 01, 2018 8:57 pm
by cybereality
Cool. Thanks for sharing.

Re: DIY NVIDIA 3D Vision emitter

Posted: Tue Feb 05, 2019 1:59 am
by nimatoed
Very cool. Wish you or someone else would sell kits for a fraction of Nvidia's exorbitant rates.

Re: DIY NVIDIA 3D Vision emitter

Posted: Sun Aug 18, 2019 10:46 am
by Guig2000
Hello, did you include the "full HD 3D IR" protocol?

Re: DIY NVIDIA 3D Vision emitter

Posted: Sun Aug 18, 2019 4:59 pm
by lukis101
Guig2000 wrote:Hello, did you include the "full HD 3D IR" protocol?
Implemented protocols (but not all of them) are found in paper "Investigating the cross-compatibility of IR-controlled
active shutter glasses"
I'm not aware of the one you mentioned but could add if given the timings

Re: DIY NVIDIA 3D Vision emitter

Posted: Mon Aug 19, 2019 2:13 pm
by Guig2000
After more search it appears that full hd ir and rf logo comes from the full hd 3d glasses initiative, that in fact includes compatibility with many protocols from different manufacturers.
https://3dvision-blog.com/tag/full-hd-3 ... nitiative/
So my question was a nonsense.

Re: DIY NVIDIA 3D Vision emitter

Posted: Wed Feb 12, 2020 12:34 pm
by SamCarm
:woot Do you have a Windows compiled version (instead of Linux) compatible with :shutter Nvidia 3d vision? The code is very complicated. And also the G05-A model glasses appear to be Bluetooth as well, not just IR :geek: . Is that the only glasses it works with?

Re: DIY NVIDIA 3D Vision emitter

Posted: Thu Feb 13, 2020 1:47 pm
by Losti
WOOW does this means if my 3d-vision 2 pyramide dies, i can make it by my own???

Re: DIY NVIDIA 3D Vision emitter

Posted: Sat Feb 22, 2020 10:35 am
by jayshay
hi, thanks for posting this. I think with the release of all the 4K 120hz TV's over the past year, we all want to try this! Is there any more info on this? Has anybody got this to actually work?

Re: DIY NVIDIA 3D Vision emitter

Posted: Mon Feb 24, 2020 6:17 am
by Alleostro
Awesome project, thx for sharing this! I def wannat try it