I think you would have to open up the glasses and switch the wiring like they did to make 3d vision glasses only see 2d except left eyes for right and right eye for left. Might void your warrenty and is not easy to do. The thing is how do you suppose an inverter box could work with 3d vision? Hook something to the emitter box? I heard someone doing that in the DIY section maybe look there.

swapping the wiring in the glasses is definitely easier than inverting the signal at the transmitter. To do that you need to understand the timings of the signals and send the opposite one.

Well just by looking at the 3D Vision glasses it looks as if the circuit board is in each side of the Arm of the Glasses. The Wires would be on the outside of the glasses and not to clean??. I would also have to lengthen each wire.. I dont think I want to do the wire switch???

I will either have to wear them upside down or get help making an inverter!!

I recall someone figured out a hack so they didn't have to wear the glasses upside-down or maybe I'm just imagining things.

a hack with the drivers or the emitter unit??

No, some physical hack. I just don't remember what it was (or maybe I'm confusing things).

Could people use the new 3Dvision hack with old edimensional type glasses?

viewtopic.php?f=3&t=9990&start=30

If page-flipping is enabled you just need a sync-extractor of some sort right?

Would the normal edimensional dongle work? Or maybe one of these designs:

http://translate.googleusercontent.com/translate_c?hl=en&sl=ru&u=http://kostasoft.com/index.php%3Fmod%3Dpages%26page%3DShutterControl&prev=/search%3Fq%3Dhttp://Kostasoft.com%26hl%3Den%26prmd%3Divns&rurl=translate.google.co.uk&twu=1&usg=ALkJrhjbe5ObgV2zVZgfRaoOH7MRX0WEDw
http://www.int03.co.uk/crema/hardware/stereo/index.html
http://nextstepsolutions.co.uk/home/node/11

I would be interested to know if anyone can test it.

I will test it now, will post on my results.

Thanks! Do your Edimensional glasses normally take sync from the VGA dongle? I have been wondering if the Nvidia emitter could work as a stand-alone emitter just using its VESA sync port? Maybe on a rear-projection DLPTV without the USB connected to the PC at all? The VESA sync port has 5v power so it could work? I think there are going to be a few of them going cheap on eBay now...

Yes i get the sync from my dongle as my wired e-dims are connected directly to the dongle. And i activate them with a software application.

I don't know what i am doing wrong but the USB input device failed to install.

I ran the dsf x64 installer
then clicked init_x64.bat , that loaded and closed
then i clicked enablestereo.bat , brings up the console and starts to install the drivers for emulation but it fails to install the input driver.
Do I need to uninstall my stereo dongle driver from nvidia you think?

Yes try re-installing the nvidia emitter driver with the emulator window still running, maybe reboot first though, can you see anything listed in device manager? You might also want to disable user account control, run the bats as admin, and if your Antivirus has a script blocker turn it off. You have unplugged the real emitter right?

Yes I unplugged the emitter but I will try to install the stereoscopic emitter software this time. It could be just my system as it never wanted to install hacked software.

Files Attatched! & also here: http://hotfile.com/dl/111389928/3d22e5e ... r.zip.html

The great thing about this "hack" is that NO Nvidia files are modified,

Microsoft wrote 99% of it, our Russian friend just made a small patch to SoftHidReceiver.dll - genius!

I still scanned everything and it's 100% clean & very stable on my system:

http://www.virustotal.com/file-scan/rep ... 1300919211

I guess i might not be able to test this out.

I unplugged my nvidia dongle loaded the enablestereo.bat with dsf x64 installed and also loading the init_x64.bat and the enablestereo.bat console pops up and trys to load
the drivers for input device and i checked the device in device manager and it shows it as "cannot start code 10"

I tried without and with the nvidia stereoscopic emitter drivers and both don't load this emulated driver. Sounds like everyone else can get it to work though. I kind of wanted to use
it without my other edid hack.

Very strange? You should only run the init.bat once, if you have done it several times maybe uninstall DSF and start over.

Maybe try using the DEVMGR_SHOW_NONPRESENT_DEVICES variable to remove ghost devices: http://support.microsoft.com/kb/315539

I'd also reboot between each step, not sure what else to suggest?

Good luck with it, I hope you get it working.

So good news, I got it working! Just had to reboot after each step and turn off UAC user account control. I had the nvidia stereoscopic emitter drivers uninstalled and when loading
enablestereo.bat it was asking for the drivers now. So i installed nvidia stereoscopic emitter drivers and now its working. I guess the main problem i was having was the UAC cause once I turned that off and loaded the init_x64.bat and rebooted everything else seemed to work.

I also tested this out with my e-dims on my projector connected to a e-dim dongle with wired glasses. The nvidia stereoconnection is "generic crt monitor" and I can see stereo with my glasses just the same as with my nvidia hardware emitter connected. Glad its working, now to tell the whole community about it.

Glad you are up and running. I have posted this in a few places already, but help spread the word!

I was thinking about starting a dedicted thread but for the moment we could continue this one:

viewtopic.php?f=3&t=9990&start=30

Wow,
I think I need to speed up the development of the emitter viewtopic.php?f=26&t=13012, so it can suit for NVDIA 3D vision and IZ3d.

i use x3d shutter glasses on 6800 with crt
i can turn on glasses on xp/vista/7
on xp i use 162.50
on vista/7 iz3d
i think if something change in regedit,or who have nvision,attach nvidia here and i will checkin

Hi, I think you will need a newer video card like at least an 8000 series card. Nvidia 3d vision only works from like 8400 - gtx590 i think. Other than that you should be able to get stereo3d to work with your setup on windows 7 with this software emitter emulator.

i forgot write that i can test on 8800 gts 640

rename to .jps